Milestone XProtect Enterprise 2014 Manuel d'utilisateur Page 99
- Page / 218
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Milestone XProtect
®
Enterprise
2014
Administrator's Manual
www.milestonesys.com
99
Advanced configuration
Name
Description
Show privacy mask
Turn the red area indicating privacy masking on or off. Turning off
the red area may provide a less obscured view of the preview
image.
Clear
Clear the privacy masking.
360° lens
360° lens technology allows you to view 360° panoramic video through an advanced lens. If a camera
is going to use 360° lens technology, you must enable the technology and, in some cases, enter a
special license key.
Name
Description
Enable 360° lens
Select check box to enable use of the 360° lens technology and to
be able to specify further properties.
Enable panomorph support
Select to enable panomorph support. Panomorph is an advanced
technology can provide high resolution in zones of interest, while at
the same time using fewer pixels than conventional fisheye
solutions.
Immervision Enables
®
panomorph RPL number
When you enable the panomorph support functionality, you must
also select a Registered Panomorph Lens (RPL) number from the
ImmerVision Enables
®
panomorph RPL number list. This is to
ensure that the lens is correctly identified and configured with the
lens used with the camera. You can usually find the RPL number on
the lens itself or on the box it came in.
If you, at some point, want to add additional types of lenses, go to
File and select Import new lens types. Locate the .xml file that
contains information about the lens type and press OK.
For details of ImmerVison, panomorph lenses, and RPLs, see
http://www.immervision.com/en/home/index.php.
Camera position/orientation
Choose whether the camera is mounted in the ceiling, on a wall or
on ground level.
Enable fisheye support
Select to enable fisheye support. Fisheye technology uses a wide-
angle lens to capture a hemispherical image, which can then be de-
warped through configured fisheye settings (see "Fisheye" on page
100) for the camera in question.
License key
If required, enter your special fisheye license key and click OK, after
which you can configure fisheye settings for camera(s) attached to
the hardware device.
If you are unsure if you need a special fisheye license key, contact your system vendor for further
information.
- Administrator's Manual 1
- Contents 2
- Before you start 10
- About administrator rights 11
- About daylight saving time 11
- About time servers 11
- About virus scanning 12
- System overview 13
- Clients 15
- Install silently 16
- Milestone Mobile client 17
- XProtect Web Client 19
- Recording Server Manager 20
- XProtect Download Manager 21
- Hiding and removing features 22
- Licenses 24
- About replacing cameras 25
- Install and upgrade 27
- Install video device drivers 29
- Upgrade 29
- First time use 33
- Best practices 34
- Power outages: use a UPS 35
- Print help topics 36
- About restarting services 37
- Monitor storage space usage 37
- Getting started 39
- Add hardware wizard 40
- Express 41
- Import from CSV file 43
- Configure storage wizard 44
- Manage user access wizard 55
- Advanced configuration 57
- Configure hardware devices 59
- Delete hardware devices 59
- Camera and database action 60
- Hardware properties 61
- PTZ device (properties) 63
- Speaker properties 64
- About database resizing 65
- About motion detection 65
- Disabled motion detection 66
- Motion detection sensitivity 66
- Online periods 67
- E-mail notification 67
- SMS notification 68
- Set up a profile 68
- Configure motion detection 69
- Disable or delete cameras 69
- Video recording (properties) 73
- Regular frame rate mode: 76
- Speedup frame rate mode: 77
- Dual stream: 78
- Manual recording 79
- Frame rate - MJPEG 80
- Frame Rate - MPEG 83
- Audio recording 84
- Audio selection 85
- Camera properties 86
- MJPEG video format 88
- Regular frame rate mode 88
- Speedup frame rate mode 88
- Dual stream 89
- MPEG video format 89
- Frame rate 89
- Recording 91
- Event notification 95
- Privacy masking 98
- 360° lens 99
- Fisheye 100
- PTZ preset positions 101
- PTZ patrolling 103
- Patrolling list 104
- PTZ scanning 104
- PTZ on event 105
- Microphones 106
- Microphone (properties) 107
- Events and output 108
- Add an analytics event 110
- Add a hardware input event 110
- Add a hardware output 111
- Add a manual event 112
- Add a generic event 112
- Add a timer event 113
- Test a generic event 114
- General event properties 116
- Events and output properties 117
- Hardware input event 118
- Hardware output 120
- Manual event 120
- Timer event 121
- Generic event 122
- (indicated in red) 123
- Scheduling and archiving 125
- About archiving 126
- About archiving locations 127
- About archiving audio 128
- About archiving schedules 129
- Scheduling all cameras 131
- Scheduling options 133
- Archiving 133
- Online period 134
- Speedup 135
- About Matrix video sharing 136
- About Matrix-recipients 136
- Configure Matrix 137
- Matrix properties 137
- Matrix event control 138
- About logs 139
- Log locations 140
- Log structures 141
- Log integrity checks 141
- Log properties 142
- Audit Log 143
- Notifications 144
- Attachment Settings (email) 145
- Server Settings (email) 146
- About SMS 147
- Configure SMS notifications 147
- SMS properties 147
- Server Settings (SMS) 148
- Scheduling 149
- Central 150
- Access control 151
- Steps in this wizard: 152
- Associated cameras 152
- Final summary 152
- Access control properties 153
- Access Control Actions 155
- Server access 158
- Configure server access 159
- Server access properties 159
- Local IP ranges 160
- Master/Slave 161
- Slave server properties 162
- Update status on slaves 162
- About users 163
- Add basic users 163
- Add Windows users 163
- Add user groups 164
- User properties 165
- General access 166
- Camera access 166
- Alarm management 168
- Access control management 168
- Services 169
- Servers 170
- About Video push 171
- Add/edit a Mobile server 171
- Add a Video push channel 171
- Mobile server settings 173
- Video Push 174
- Automatic exports 175
- Exported recordings 175
- Performance 176
- Level 2 177
- Level 3 177
- Mobile Server Manager 178
- About show status 179
- Edit certificate 179
- Show/edit port numbers 180
- About alarms 181
- About maps 182
- Add an alarm 183
- Alarms properties 184
- Alarm data settings 185
- Sound settings 186
- Time profile 187
- MIP plug-ins 188
- Settings 189
- Options 190
- Language 191
- User Interface 192
- Default File Paths 192
- Access Control Settings 192
- Analytics Event Settings 193
- Event Server Settings 193
- System maintenance 195
- Restore system configuration 196
- Glossary of Terms 202
Produits connexes et manuels pour Logiciel Milestone XProtect Enterprise 2014
Logiciel Milestone M50 Manuel d'utilisateur
(215 pages)
(215 pages)
Logiciel Milestone M10 Manuel d'utilisateur
(38 pages)
(38 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.443 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels