Milestone XProtect Professional 2014 Manuel d'utilisateur Page 82
- Page / 218
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Milestone XProtect
®
Professional
2014
Administrator's Manual
www.milestonesys.com
82
Advanced configuration
Name
Description
Frame Rate
Speedup frame rate for viewing video from the camera. Select
number of frames, then select the time unit interval (second, minute
or hour). The frame rate must be higher than the frame rate
specified under normal mode.
Time Unit
Select required unit for live and recording frame rates (per second,
minute, or hour). Note that you can only select time bases that let
you speed up frame rates. Example: If you have specified 15
frames per second in normal mode, you cannot specify 16 frames
per minute or hour in speedup mode.
Speedup On
Motion Detection: Select this to speed up when motion
(see "Motion detection & exclude regions" on page 96) is
detected. Normal frame rates will be resumed immediately
after the last motion is detected.
Event: Select this to speed up when an event occurs and
until another event occurs. Use of speedup on event
requires that events have been defined, and that you select
start and stop events in the neighboring columns.
Use the Configure events list, located below the other
fields to define events that suit your needs.
Motion Detection & Event: Select this to speed up when
motion is detected, or when an event occurs and until
another event occurs. Remember to select start and stop
events in the neighboring columns.
Schedule Only
Select this to speed up according to the camera's speedup
schedule (see "Speedup" on page 135) only.
Start Event
Select required start event. The camera will begin using the
speedup frame rates when the start event occurs.
Stop Event
Select required stop event. The camera will return to the normal
frame rates when the stop event occurs.
Camera
Click the Open button to configure detailed and/or camera-specific
settings (such as event notification, PTZ preset positions, and
fisheye view areas) for the selected camera.
Properties available in all XProtect software versions:
Live Frame Rate
Required average frame rate for live video from the camera. Select
number of frames, then select the time unit interval (second, minute
or hour). The frame rate must be higher than the frame rate
specified under normal mode.
If the camera supports dual stream and dual stream is enabled, the
Live Frame Rate column will be read-only with the value Dual
streaming—which cannot be altered.
- Administrator's Manual 1
- Contents 2
- Before you start 10
- About daylight saving time 11
- About time servers 11
- About virus scanning 12
- System overview 13
- Clients 15
- Install silently 16
- Milestone Mobile client 17
- XProtect Web Client 19
- Recording Server Manager 20
- XProtect Download Manager 21
- Hiding and removing features 22
- Licenses 24
- About replacing cameras 25
- Install and upgrade 27
- Install video device drivers 29
- Upgrade 29
- First time use 33
- Best practices 34
- Power outages: use a UPS 35
- Print help topics 36
- About restarting services 37
- Monitor storage space usage 37
- Getting started 39
- Add hardware wizard 40
- Express 41
- Import from CSV file 43
- Configure storage wizard 44
- Manage user access wizard 55
- Advanced configuration 57
- Configure hardware devices 59
- Delete hardware devices 59
- Camera and database action 61
- Speaker properties 62
- Hardware properties 62
- PTZ device (properties) 63
- About database resizing 65
- About motion detection 65
- Enabled motion detection 66
- Disabled motion detection 66
- Motion detection sensitivity 66
- Online periods 67
- E-mail notification 68
- SMS notification 68
- Set up a profile 68
- Configure motion detection 69
- Disable or delete cameras 69
- Video recording (properties) 73
- Regular frame rate mode: 76
- Speedup frame rate mode: 77
- Dual stream: 78
- Manual recording 79
- Frame rate - MJPEG 80
- Frame Rate - MPEG 83
- Audio recording 84
- Audio selection 85
- Camera properties 86
- MJPEG video format 88
- Regular frame rate mode 88
- Speedup frame rate mode 88
- Dual stream 89
- MPEG video format 89
- Frame rate 89
- Recording 91
- Event notification 95
- Privacy masking 98
- 360° lens 99
- Fisheye 100
- PTZ preset positions 101
- PTZ patrolling 103
- Patrolling list 104
- PTZ scanning 104
- PTZ on event 105
- Microphones 106
- Microphone (properties) 107
- Events and output 108
- Add an analytics event 110
- Add a hardware input event 110
- Add a hardware output 111
- Add a manual event 112
- Add a generic event 112
- Add a timer event 113
- Test a generic event 114
- General event properties 116
- Events and output properties 117
- Hardware input event 118
- Hardware output 120
- Manual event 120
- Timer event 121
- Generic event 122
- (indicated in red) 123
- Scheduling and archiving 125
- About archiving 126
- About archiving locations 127
- About archiving audio 128
- About archiving schedules 129
- Scheduling all cameras 131
- Scheduling options 133
- Archiving 133
- Online period 134
- Speedup 135
- About Matrix video sharing 136
- About Matrix-recipients 136
- Configure Matrix 137
- Matrix properties 137
- Matrix event control 138
- About logs 139
- Log locations 140
- Log structures 141
- Log integrity checks 141
- Log properties 142
- Audit Log 143
- Notifications 144
- Attachment Settings (email) 145
- Server Settings (email) 146
- About SMS 147
- Configure SMS notifications 147
- SMS properties 147
- Server Settings (SMS) 148
- Scheduling 149
- Central 150
- Access control 151
- Steps in this wizard: 152
- Associated cameras 152
- Final summary 152
- Access control properties 153
- Access Control Actions 155
- Server access 158
- Configure server access 159
- Server access properties 159
- Local IP ranges 160
- Master/Slave 161
- Slave server properties 162
- Update status on slaves 162
- About users 163
- Add basic users 163
- Add Windows users 163
- Add user groups 164
- User properties 165
- General access 166
- Camera access 166
- Alarm management 168
- Access control management 168
- Services 169
- Servers 170
- About Video push 171
- Add/edit a Mobile server 171
- Add a Video push channel 171
- Mobile server settings 173
- Video Push 174
- Automatic exports 175
- Exported recordings 175
- Performance 176
- Level 2 177
- Level 3 177
- About Mobile Server Manager 178
- Log Settings 178
- Mobile Server Manager 178
- About show status 179
- Edit certificate 179
- Show/edit port numbers 180
- About alarms 181
- About maps 182
- Add an alarm 183
- Alarms properties 184
- Alarm data settings 185
- Sound settings 186
- MIP plug-ins 187
- Settings 188
- Options 189
- User Interface 190
- Default File Paths 191
- Analytics Event Settings 191
- Event Server Settings 192
- System maintenance 194
- Restore system configuration 195
- Glossary of Terms 201
Produits connexes et manuels pour Logiciel Milestone XProtect Professional 2014
Logiciel Milestone M50 Manuel d'utilisateur
(215 pages)
(215 pages)
Logiciel Milestone M10 Manuel d'utilisateur
(38 pages)
(38 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.437 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels