Milestone XProtect Professional 2014 Manuel d'utilisateur Page 54
- Page / 218
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Milestone XProtect
®
Professional
2014
Administrator's Manual
www.milestonesys.com
54
Getting started
You can configure motion detection settings for each camera, or for several cameras at once. Use the
list in the left pane of the wizard window to select cameras. To select several cameras at a time, press
CTRL or SHIFT while you select. When you select a camera, you see a preview from that camera. If
you select several cameras, you see a preview from the last camera you select. A green area in the
preview indicates motion.
Properties available in all XProtect software versions:
Name
Description
Sensitivity
Adjust the Sensitivity slider so that irrelevant background noise is
filtered out, and only real motion is shown in green. Alternatively,
specify a value between 0 and 256 in the field next to the slider to
control the sensitivity setting.
The slider determines how much each pixel must change before it
is regarded as motion. With a high sensitivity, very little change in a
pixel is required before it is regarded as motion. The more you drag
the slider to the left, the more of the preview becomes green. This is
because with high sensitivity, even the slightest pixel change is
regarded as motion.
Motion
Adjust the Motion slider so that motion detection is only triggered
by the required level of motion. The selected motion level is
indicated by the black vertical line in the Level bar above the
sliders. The black vertical line serves as a threshold. When motion
is above (to the right of) the selected level, the bar changes color
from green to red, indicating a positive motion detection.
Alternatively, specify a value between 0 and 10000 in the field on
the left to control the motion setting.
The more you drag the slider to the left, the more positive motion
detections you see because less change will be needed to trigger a
positive motion detection. The number of positive motion detections
may also affect the amount of video you record, the amount of
notifications you receive and more.
Detection interval
Specify how often motion detection analysis is carried out on video
from the camera. The default is every 240 milliseconds (close to
once a quarter of a second). The interval is applied regardless of
your cameras' frame rate settings.
Adjusting this setting can help lower the amount of system
resources used on motion detection.
- Administrator's Manual 1
- Contents 2
- Before you start 10
- About daylight saving time 11
- About time servers 11
- About virus scanning 12
- System overview 13
- Clients 15
- Install silently 16
- Milestone Mobile client 17
- XProtect Web Client 19
- Recording Server Manager 20
- XProtect Download Manager 21
- Hiding and removing features 22
- Licenses 24
- About replacing cameras 25
- Install and upgrade 27
- Install video device drivers 29
- Upgrade 29
- First time use 33
- Best practices 34
- Power outages: use a UPS 35
- Print help topics 36
- About restarting services 37
- Monitor storage space usage 37
- Getting started 39
- Add hardware wizard 40
- Express 41
- Import from CSV file 43
- Configure storage wizard 44
- Manage user access wizard 55
- Advanced configuration 57
- Configure hardware devices 59
- Delete hardware devices 59
- Camera and database action 61
- Speaker properties 62
- Hardware properties 62
- PTZ device (properties) 63
- About database resizing 65
- About motion detection 65
- Enabled motion detection 66
- Disabled motion detection 66
- Motion detection sensitivity 66
- Online periods 67
- E-mail notification 68
- SMS notification 68
- Set up a profile 68
- Configure motion detection 69
- Disable or delete cameras 69
- Video recording (properties) 73
- Regular frame rate mode: 76
- Speedup frame rate mode: 77
- Dual stream: 78
- Manual recording 79
- Frame rate - MJPEG 80
- Frame Rate - MPEG 83
- Audio recording 84
- Audio selection 85
- Camera properties 86
- MJPEG video format 88
- Regular frame rate mode 88
- Speedup frame rate mode 88
- Dual stream 89
- MPEG video format 89
- Frame rate 89
- Recording 91
- Event notification 95
- Privacy masking 98
- 360° lens 99
- Fisheye 100
- PTZ preset positions 101
- PTZ patrolling 103
- Patrolling list 104
- PTZ scanning 104
- PTZ on event 105
- Microphones 106
- Microphone (properties) 107
- Events and output 108
- Add an analytics event 110
- Add a hardware input event 110
- Add a hardware output 111
- Add a manual event 112
- Add a generic event 112
- Add a timer event 113
- Test a generic event 114
- General event properties 116
- Events and output properties 117
- Hardware input event 118
- Hardware output 120
- Manual event 120
- Timer event 121
- Generic event 122
- (indicated in red) 123
- Scheduling and archiving 125
- About archiving 126
- About archiving locations 127
- About archiving audio 128
- About archiving schedules 129
- Scheduling all cameras 131
- Scheduling options 133
- Archiving 133
- Online period 134
- Speedup 135
- About Matrix video sharing 136
- About Matrix-recipients 136
- Configure Matrix 137
- Matrix properties 137
- Matrix event control 138
- About logs 139
- Log locations 140
- Log structures 141
- Log integrity checks 141
- Log properties 142
- Audit Log 143
- Notifications 144
- Attachment Settings (email) 145
- Server Settings (email) 146
- About SMS 147
- Configure SMS notifications 147
- SMS properties 147
- Server Settings (SMS) 148
- Scheduling 149
- Central 150
- Access control 151
- Steps in this wizard: 152
- Associated cameras 152
- Final summary 152
- Access control properties 153
- Access Control Actions 155
- Server access 158
- Configure server access 159
- Server access properties 159
- Local IP ranges 160
- Master/Slave 161
- Slave server properties 162
- Update status on slaves 162
- About users 163
- Add basic users 163
- Add Windows users 163
- Add user groups 164
- User properties 165
- General access 166
- Camera access 166
- Alarm management 168
- Access control management 168
- Services 169
- Servers 170
- About Video push 171
- Add/edit a Mobile server 171
- Add a Video push channel 171
- Mobile server settings 173
- Video Push 174
- Automatic exports 175
- Exported recordings 175
- Performance 176
- Level 2 177
- Level 3 177
- About Mobile Server Manager 178
- Log Settings 178
- Mobile Server Manager 178
- About show status 179
- Edit certificate 179
- Show/edit port numbers 180
- About alarms 181
- About maps 182
- Add an alarm 183
- Alarms properties 184
- Alarm data settings 185
- Sound settings 186
- MIP plug-ins 187
- Settings 188
- Options 189
- User Interface 190
- Default File Paths 191
- Analytics Event Settings 191
- Event Server Settings 192
- System maintenance 194
- Restore system configuration 195
- Glossary of Terms 201
Produits connexes et manuels pour Logiciel Milestone XProtect Professional 2014
Logiciel Milestone M50 Manuel d'utilisateur
(215 pages)
(215 pages)
Logiciel Milestone M10 Manuel d'utilisateur
(38 pages)
(38 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.126 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels